1jz 2jz 7m

AllMotorJunkie · 07-31-2006, 11:57 PM

hi guys, as i stated in previous thread im new to supras, and bought a 85 celica supra. i gather this is the 5m motor? it has 202k miles on it, runs and is auto. i bought it for a daily driver for the moment. but anyways can you guys give me info on the diff motors that are easily fitable into this chasis? i searched and most sites dont tell hp/tq/cr/ and other specs i wanna know, so if you guys can tell me some info on the 5m 7m 1jz and 2jz and differences of them id appreciate it, thanks!

suprasforlife · 08-06-2006, 09:27 AM

The only motor that goes in easily is a 5m, all the others require mods. Did you search here because being a supra forum I'm sure your question has been asked about a thousand times.

supra1985turbo · 09-25-2006, 05:06 PM

I beg to differ, the 5M, 6M, 7M. All use the same block so they will bolt right up to the tranny and the mounts are the same, the only thing you will have to do. if you put the 7m in you will have to change ecu and the wiring. the 6m from my research you will only have to change minor things. The other engines will require mods to the fram and chasis.

midwestmk2 · 09-26-2006, 02:13 AM

Yes the 5,6,7m's all use the same blocks but the motor mounts do vary between models and years.The 1'2jz series motors on the other hand will drop in but you will have to fab your own motor mounts,tranny mounts,wiring,etc..You will not have to do any chassis or frame mods..

suprra_girl · 09-26-2006, 10:00 AM

yeps M series motors.. and away ya go, just gotta wire it in and stuff then

and if you get them G series motors also

if you do wanna go G series route lmk and i will source some engine mounts for the mk2 chassis

supra1985turbo · 09-26-2006, 10:54 AM

Sorry if I was wrong!!!!!!!!!!!!!!Its been a while since I was going to do the 2jz trade and 6 speed tranny. The research I did about three or four years ago showed that you had to do some major fab and mod to the mounts frame and a little to the firewall for the tranny. Since then they might have made the fab easier.

midwestmk2 · 09-27-2006, 04:34 AM

With the right mods you can have more power in your 5/6m motors N/A than a some boosted 7m's..Because the 5,6m's have the 12 valve setup the valves are larger and can withstand more heat build up than the little valves in the 24 valve 7m heads..A 5/6m motor can be pushed to 240hp easily with the right internal mods..Cams,pistons,rods,port@polish,etc..Now with a turbo thrown in there you will be able to desimate almost any 7m..Because the valves can handle more heat that means they can also handle more boost..So build up your bottom end get some forged pistons and boost it on up and kick ass in your MKII that is already got the weight advantage over the PIG and JellyBean!!

07-31-2006, 11:57 PM	#1
AllMotorJunkie Stock Join Date: Jul 2006 Location: california Posts: 3	1jz 2jz 7m hi guys, as i stated in previous thread im new to supras, and bought a 85 celica supra. i gather this is the 5m motor? it has 202k miles on it, runs and is auto. i bought it for a daily driver for the moment. but anyways can you guys give me info on the diff motors that are easily fitable into this chasis? i searched and most sites dont tell hp/tq/cr/ and other specs i wanna know, so if you guys can tell me some info on the 5m 7m 1jz and 2jz and differences of them id appreciate it, thanks!

09-25-2006, 05:06 PM	#3
supra1985turbo 3" Exhaust Join Date: Sep 2006 Location: Kingwood, TX Posts: 63	engine fitup in 85 supra I beg to differ, the 5M, 6M, 7M. All use the same block so they will bolt right up to the tranny and the mounts are the same, the only thing you will have to do. if you put the 7m in you will have to change ecu and the wiring. the 6m from my research you will only have to change minor things. The other engines will require mods to the fram and chasis.

09-26-2006, 02:13 AM	#4
midwestmk2 3" Exhaust Join Date: May 2005 Location: STL ,MO. Posts: 206	Yes the 5,6,7m's all use the same blocks but the motor mounts do vary between models and years.The 1'2jz series motors on the other hand will drop in but you will have to fab your own motor mounts,tranny mounts,wiring,etc..You will not have to do any chassis or frame mods.. __________________ 83 p-type,5spd,4;10 gears,New 86 cressida 5MGE 195hp,HKS metal head gasket,Cressida injectors,d-port intake runners,No EGR,No cat,Tweaked MAF,Custom cold air intake,Custom rear strut bar,Perfection clutch,Custom 3inch exhaust,4inch bazooka muffler,,Only 2700lbs,, COME AND GET IT!IF YOU DARE!! Please no Honduuuuhhhs!!! http://www.cardomain.com/ride/858848/2

09-26-2006, 10:00 AM	#5
suprra_girl 7M POWAH! ;) Join Date: Jun 2004 Location: New Zealand Posts: 2,312	yeps M series motors.. and away ya go, just gotta wire it in and stuff then and if you get them G series motors also if you do wanna go G series route lmk and i will source some engine mounts for the mk2 chassis __________________ Please use the forum to ask your questions as they will get replied to much faster than pming me Pics of my build. "Good girls are just bad girls that don't get caught" Do a diagnostic first!

09-27-2006, 04:34 AM	#7
midwestmk2 3" Exhaust Join Date: May 2005 Location: STL ,MO. Posts: 206	With the right mods you can have more power in your 5/6m motors N/A than a some boosted 7m's..Because the 5,6m's have the 12 valve setup the valves are larger and can withstand more heat build up than the little valves in the 24 valve 7m heads..A 5/6m motor can be pushed to 240hp easily with the right internal mods..Cams,pistons,rods,port@polish,etc..Now with a turbo thrown in there you will be able to desimate almost any 7m..Because the valves can handle more heat that means they can also handle more boost..So build up your bottom end get some forged pistons and boost it on up and kick ass in your MKII that is already got the weight advantage over the PIG and JellyBean!! __________________ 83 p-type,5spd,4;10 gears,New 86 cressida 5MGE 195hp,HKS metal head gasket,Cressida injectors,d-port intake runners,No EGR,No cat,Tweaked MAF,Custom cold air intake,Custom rear strut bar,Perfection clutch,Custom 3inch exhaust,4inch bazooka muffler,,Only 2700lbs,, COME AND GET IT!IF YOU DARE!! Please no Honduuuuhhhs!!! http://www.cardomain.com/ride/858848/2

08-06-2006, 09:27 AM	#2
suprasforlife 3" Exhaust Join Date: Jun 2006 Location: Montana Posts: 71	The only motor that goes in easily is a 5m, all the others require mods. Did you search here because being a supra forum I'm sure your question has been asked about a thousand times.

09-26-2006, 10:54 AM	#6
supra1985turbo 3" Exhaust Join Date: Sep 2006 Location: Kingwood, TX Posts: 63	Sorry if I was wrong!!!!!!!!!!!!!!Its been a while since I was going to do the 2jz trade and 6 speed tranny. The research I did about three or four years ago showed that you had to do some major fab and mod to the mounts frame and a little to the firewall for the tranny. Since then they might have made the fab easier.