01-04-2008, 04:24 AM | #1 |
Intake
Join Date: Jan 2008
Location: Lancaster PA
Posts: 45
|
Intake help!
I just joined the ranks today when I bought an '88 Supra N/A. (This must be what its like to come home from Iraq - I was a Mitsu guy for about 6 years which equivalates to jail or military service in a hot zone, or an uncomfortable STD). This supra drove out of a time warp from 1988 - looks brand new in, out, and under - completley stock down to the head unit (really neat, by the way). I would like to make a few adjustments to wake the car up a bit, but i'm not willing to comprimise the integrity of the origional parts.
Does anyone know of a manufacturer of a cold air intake? perhaps just an adapter for my cone air filter would do the job cost-effectively. Are there any suggestions for an aftermarket ignition system? I've wired big block chevy's (350, 454) with MSD systems from mod to plug(plugs were ACDelco rapid fires, actually) but didnt notice any significant change. What are the recommended SFMS platforms for my supra? Where can I find air dam's for the front of the car? Any advice would be great! |
01-04-2008, 07:33 AM | #2 |
Super Moderator
Join Date: May 2007
Location: Billings, Montana
Posts: 1,034
|
K&N makes good products, such as the cold air intake you were speaking of, and I believe that you can get a MAF sensor adapter/filter from them as well. However, the downside to K&N filter's is that when you clean it, you'll have to re-oil it, possibly causing damage to intake sensors. I believe it's AEM that has dry filters (don't need to oil them), which might be a little more, but better for your car in the long run.
If you're looking to keep your 7MGE Supra (7MGE being your N/A's engine code) as a reliable commuter, you'll do your car could use a good tune up. Get the timing checked (or do it yourself), check/replace the belts and hoses (don't forget the systems of vacuum hoses), replace spark plugs, distributor cap, spark plug wires, etc...
__________________
1989 7MGTE R154 Targa Top White Package w/Blue Interior Driftmotion 57trim CT26, Upgraded Intercooler, 2.25" Hard Pipes, 3" Turbo Back Exhaust with Test Pipe, HKS VPC w/GM 3 bar MAP sensor, APEXi S-AFC, Walbro 255lph fuel pump, ProSport EVO Series Boost / Fuel Pressure / AFR gauges, Lotek a Pillar Gauge Pod, HKS Type 0 Turbo Timer, Eibach Lowering Springs, Tokico Illumina II TEMS struts, custom powder coated Motegi Racing TrakLite wheels |
01-04-2008, 12:28 PM | #3 |
3" Exhaust
Join Date: Oct 2007
Location: Aruba
Posts: 113
|
this would help maybe im too late but this is what i got
1986-1992 Toyota Supra - Spectre Mass Air Flow Sensor Adaptor you see the holes on the adapter but that is for show, the holes you will need to drill yourself i got mine without the holes. Last edited by SilenceboneSupra; 01-04-2008 at 12:43 PM. Reason: mistake |
01-04-2008, 12:37 PM | #4 |
3" Exhaust
Join Date: Oct 2007
Location: Aruba
Posts: 113
|
also check out the Weapon R Intake, these intakes are the best from my view. here is the link to one!
Weapon*R Racing Development Last edited by SilenceboneSupra; 01-04-2008 at 12:49 PM. |
01-05-2008, 12:06 AM | #5 |
1000whp postwhore
Join Date: Jun 2005
Location: Mojave Desert, Calif.
Posts: 1,705
|
ebay.filter and adaptor..$25
__________________
Had a Red 1989 N/A. Automatic. Sports Pkg. w/wing. TEMS, and some nice MODS. Sold to a friend 10/08/08. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Intake Question | EvilDragun | MKIII Supra | 18 | 04-15-2008 04:05 AM |
Cleaning Intake & Injectors | mrnickleye | Supra FAQ | 6 | 03-23-2007 04:26 AM |
5mge intake manifold upgrade | Allen Crump | Non-Generation Specific Questions | 1 | 11-02-2006 01:53 AM |
intake manifold has coolant what did i do wrong? | 91toy supra | MKIII Supra | 6 | 09-16-2006 02:46 PM |
custom intake manifold | j3pz | MKIII Supra | 8 | 12-07-2005 06:23 PM |