First Gear pops out?

FunWheelDrive · 03-14-2008, 03:50 AM

After putting a 3inch exhaust put on my car, i've been driving about 100miles and on this last drive at the end of the drive i'll go to put it in first by going second to first, and it "seems" like it's going in, then you let the clutch out, and you hear a POP as soon as the clutch grabs and the car goes into neutrul.

If i put it really slowely into second to first really slow or really aggressily then it'll go in sometimes, it's half and half, though the last 5 times i tried it went into first and stuck. The tranny shifts completely the same as it did before, no grinds nothing, i check my clutch fluid level and it's just above the min line by like 1-2mm. I'm going to try and bleed my clutch tommorow, also important to note, when the car is in first and it's moving only once has it came out under light accel, never under heavy, and it will pop out 70% of the time under decell. I don't think it's my tranny syncro's because it's so inconsistant. Also my master cylinder looks to be leaking aswell.

So, did my tranny on my 7m-GTE decide it doesn't want to be a tranny anymore or is it just the clutch no disenging all the way? Please help.

CyFi6 · 03-14-2008, 06:50 AM

Fix the leaking master cylinder and bleed the system first. Then check all your motor mounts and tranny mount and make sure your shifter is not interfering with anythhing in the interior and is all tight. If its hitting the center consle plastic thing underneath it might not be going into gear fully

FunWheelDrive · 03-14-2008, 07:04 AM

If it's worth noting anything, before it started to do it somebody asked me if it was a standard or not and i shook the shifter pretty good left to right not in any gears while the car was off. The times when it won't go into first it feels like first isn't even there, like it just feels like i'm pushing into nothing, and the tranny just makes noise as i let the clutch go.

From what i told does it sounds like a bad clutch something or master cylinder or a blown up tranny? I Just bought the car 3 weeks ago and the tranny shifts so smooth and was babied most of it's life. Thanks

CyFi6 · 03-14-2008, 08:22 AM

id pull the shifter out and inspect it, sounds like the bushing could be causing some sort of problem. When you say it pops out, do you mean if you hold the shifter it will stay in gear or it doesnt engage at all in the first place

FunWheelDrive · 03-14-2008, 04:23 PM

I never tried holding it in, but it just seems like it's not going into first all the way, but if i pump the clutch 3-4 times it normally will go into first gear and stay in. I'm pretty sure there is air in the line, i'm bleeding the line this afternoon. All the other gears seem a little harder to get into as well. I love the help keep it coming.

supramacist · 03-14-2008, 07:39 PM

master cylinder or slave cylinder hopefully.

If not, the clutch is hydraulic. That's the next stop for me.

03-14-2008, 03:50 AM	#1
FunWheelDrive Stock Join Date: Feb 2008 Location: Calgary Alberta/ Posts: 17	First Gear pops out? After putting a 3inch exhaust put on my car, i've been driving about 100miles and on this last drive at the end of the drive i'll go to put it in first by going second to first, and it "seems" like it's going in, then you let the clutch out, and you hear a POP as soon as the clutch grabs and the car goes into neutrul. If i put it really slowely into second to first really slow or really aggressily then it'll go in sometimes, it's half and half, though the last 5 times i tried it went into first and stuck. The tranny shifts completely the same as it did before, no grinds nothing, i check my clutch fluid level and it's just above the min line by like 1-2mm. I'm going to try and bleed my clutch tommorow, also important to note, when the car is in first and it's moving only once has it came out under light accel, never under heavy, and it will pop out 70% of the time under decell. I don't think it's my tranny syncro's because it's so inconsistant. Also my master cylinder looks to be leaking aswell. So, did my tranny on my 7m-GTE decide it doesn't want to be a tranny anymore or is it just the clutch no disenging all the way? Please help. Last edited by FunWheelDrive; 03-14-2008 at 05:41 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
LSD gear oil	suprabahamut	Non-Generation Specific Questions	3	05-04-2008 02:40 AM
speedometer drive gear removal	Gunnar	MKIII Supra	1	01-20-2008 08:24 PM
quick question	blacksheep	Non-Generation Specific Questions	10	01-01-2007 08:19 PM
Second Gear Sound	dcrusupra	MKIII Supra	9	12-24-2005 08:05 AM
2nd gear grind	Chomper	Non-Generation Specific Questions	1	12-14-2005 03:59 AM

03-14-2008, 06:50 AM	#2
CyFi6 3" Exhaust Join Date: Oct 2007 Location: SLO Posts: 234	Fix the leaking master cylinder and bleed the system first. Then check all your motor mounts and tranny mount and make sure your shifter is not interfering with anythhing in the interior and is all tight. If its hitting the center consle plastic thing underneath it might not be going into gear fully

03-14-2008, 07:04 AM	#3
FunWheelDrive Stock Join Date: Feb 2008 Location: Calgary Alberta/ Posts: 17	If it's worth noting anything, before it started to do it somebody asked me if it was a standard or not and i shook the shifter pretty good left to right not in any gears while the car was off. The times when it won't go into first it feels like first isn't even there, like it just feels like i'm pushing into nothing, and the tranny just makes noise as i let the clutch go. From what i told does it sounds like a bad clutch something or master cylinder or a blown up tranny? I Just bought the car 3 weeks ago and the tranny shifts so smooth and was babied most of it's life. Thanks

03-14-2008, 08:22 AM	#4
CyFi6 3" Exhaust Join Date: Oct 2007 Location: SLO Posts: 234	id pull the shifter out and inspect it, sounds like the bushing could be causing some sort of problem. When you say it pops out, do you mean if you hold the shifter it will stay in gear or it doesnt engage at all in the first place

03-14-2008, 04:23 PM	#5
FunWheelDrive Stock Join Date: Feb 2008 Location: Calgary Alberta/ Posts: 17	I never tried holding it in, but it just seems like it's not going into first all the way, but if i pump the clutch 3-4 times it normally will go into first gear and stay in. I'm pretty sure there is air in the line, i'm bleeding the line this afternoon. All the other gears seem a little harder to get into as well. I love the help keep it coming.

03-14-2008, 07:39 PM	#6
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	master cylinder or slave cylinder hopefully. If not, the clutch is hydraulic. That's the next stop for me.