in some need of help

suprakid91 · 04-18-2008, 10:46 PM

my car has been running just fine for a while now and all of the sudden all sorts of stuff goes wrong. just adding more check marks in the bank... ha. but anyways i need some help, whenever i am driving normal or getting on the gas whenever i push in the clutch to the floor and let the RPM's drop it just dies. hard. like no rough idle then die it just goes down. i have no idea what it is. i have pretty new vacuum lines and all of them are connected. i was thinking of just turning up the idle so it stays at like 1000 rpm but i have no idea where the idler screw is at. if anyone knows please share

haha so i dont know what the problem could be. any help from you guys would be great.

supramacist · 04-19-2008, 12:15 AM

I have never seen an idle screw.
ge or gte??

suprakid91 · 04-19-2008, 03:01 PM

gte. i was just wondering if it had one. but i guess not. i was just trying to get it to rev a little higher, so how would i go about doing this?

ddmcse · 04-20-2008, 04:54 PM

there is an idle screw but i wouldn't screw with it yet .
i'd check all vacuum lines and read the engine codes

you must throw a code when it dies like that

check vsv values hidden under intake they are about 50 bucks

if faulty they wreck fuel mixture , bad fuel mixture = bad idle

supramacist · 04-21-2008, 03:29 AM

N/A's have idle screws????
I'm all ears.

I have been told enough that they didn't that i just worked around it and never really payed it any mind.

cre · 04-21-2008, 03:39 AM

Actually, both GE and GTE have "idle screws" they're NOT considered a serviceable item at all. There's a reason they're not even covered in the TSRM.

As a side note, I've seen people adjust the WAY wrong things before when trying to adjust the idle... and effectively doing so but at the risk of causing damage: dash pots, air regulation screws and my favorite..... over tightening the throttle linkages so the throttle plate is always partly open and the IDL switch is never closed.

04-18-2008, 10:46 PM	#1
suprakid91 3" Exhaust Join Date: Oct 2007 Location: minnesota Posts: 119	in some need of help my car has been running just fine for a while now and all of the sudden all sorts of stuff goes wrong. just adding more check marks in the bank... ha. but anyways i need some help, whenever i am driving normal or getting on the gas whenever i push in the clutch to the floor and let the RPM's drop it just dies. hard. like no rough idle then die it just goes down. i have no idea what it is. i have pretty new vacuum lines and all of them are connected. i was thinking of just turning up the idle so it stays at like 1000 rpm but i have no idea where the idler screw is at. if anyone knows please share haha so i dont know what the problem could be. any help from you guys would be great. __________________ 91' 7m-gte, sold

04-19-2008, 03:01 PM	#3
suprakid91 3" Exhaust Join Date: Oct 2007 Location: minnesota Posts: 119	gte. i was just wondering if it had one. but i guess not. i was just trying to get it to rev a little higher, so how would i go about doing this? __________________ 91' 7m-gte, sold

04-20-2008, 04:54 PM	#4
ddmcse 500whp yet? Join Date: Jun 2005 Location: CT U.S.A. Posts: 966	there is an idle screw but i wouldn't screw with it yet . i'd check all vacuum lines and read the engine codes you must throw a code when it dies like that check vsv values hidden under intake they are about 50 bucks if faulty they wreck fuel mixture , bad fuel mixture = bad idle __________________ 300+ RW HP Dyno run, jdm,mod turbo,3"exh,electfan,greddyboost Blown HeadGasket info My Supra KiXGaS Last edited by ddmcse; 04-20-2008 at 04:58 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

04-19-2008, 12:15 AM	#2
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	I have never seen an idle screw. ge or gte??

04-21-2008, 03:29 AM	#5
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	N/A's have idle screws???? I'm all ears. I have been told enough that they didn't that i just worked around it and never really payed it any mind.

04-21-2008, 03:39 AM	#6
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Actually, both GE and GTE have "idle screws" they're NOT considered a serviceable item at all. There's a reason they're not even covered in the TSRM. As a side note, I've seen people adjust the WAY wrong things before when trying to adjust the idle... and effectively doing so but at the risk of causing damage: dash pots, air regulation screws and my favorite..... over tightening the throttle linkages so the throttle plate is always partly open and the IDL switch is never closed.