head bolts tool

mrnickleye · 05-12-2008, 02:40 AM

I bought a 6" long one from Matco Tools. Snap-On and Mac have them too.

Serge · 05-12-2008, 03:35 AM

Alright...Thank you All !
will but it tomorrow....

supramacist · 05-12-2008, 03:43 AM

You guys may think me ignorant. But it works.

I went to lowes. I bought a 4 inch long bolt with a head that fit my needs.
I bought a 2 inch long 2 way adapter type nut.

I used red loctite on it. It's what I use when I hit that portion of the engine.

It cost me less that $4.

Serge · 05-12-2008, 04:12 AM

That is interesting solution...I'll think about it
Thank you!

slader99 · 05-12-2008, 02:20 PM

I use a similar type solution. If you have lots of metric hardware around find a long bolt, two matching nuts, turn the nuts onto the end of the bolt, and lock them together. If you find its still slipping you can destry the threads of your toyota SST with a flat head screw driver. Might save a trip to the store....

Serge · 05-13-2008, 01:46 PM

this is how it looks like I took it apart...the gasket looks very badly. At list three of my cylinders are blown...

any suggestions?

supramacist · 05-13-2008, 03:23 PM

Looks like it was go or blow time.

Nice job. It looks much worse than it is serge.

Once you start cleaning it up. You'll see.

05-12-2008, 02:40 AM	#1
mrnickleye 1000whp postwhore Join Date: Jun 2005 Location: Mojave Desert, Calif. Posts: 1,705	I bought a 6" long one from Matco Tools. Snap-On and Mac have them too. __________________ Had a Red 1989 N/A. Automatic. Sports Pkg. w/wing. TEMS, and some nice MODS. Sold to a friend 10/08/08.

05-12-2008, 03:43 AM	#3
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	You guys may think me ignorant. But it works. I went to lowes. I bought a 4 inch long bolt with a head that fit my needs. I bought a 2 inch long 2 way adapter type nut. I used red loctite on it. It's what I use when I hit that portion of the engine. It cost me less that $4. Last edited by supramacist; 05-12-2008 at 05:40 AM.

05-13-2008, 01:46 PM	#6
Serge 3" Exhaust Join Date: Mar 2008 Location: WA Posts: 69	this is how it looks like I took it apart...the gasket looks very badly. At list three of my cylinders are blown... any suggestions? Attached Thumbnails

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
head bolts on jdm engine	tone loc	MKIII Supra	10	06-03-2007 09:33 PM
Head bolts	G-string	MKIII Supra	16	05-22-2007 04:22 PM
head gasket bolts	marc	MKIII Supra	6	10-23-2006 07:23 PM
Head Bolts, Or Head Studs??	ZauggIt1	MKIII Supra	2	08-08-2006 01:23 PM
ARP head bolts	Deputy99	MKIII Supra	2	07-19-2006 11:16 PM

05-12-2008, 03:35 AM	#2
Serge 3" Exhaust Join Date: Mar 2008 Location: WA Posts: 69	Alright...Thank you All ! will but it tomorrow....

05-12-2008, 04:12 AM	#4
Serge 3" Exhaust Join Date: Mar 2008 Location: WA Posts: 69	That is interesting solution...I'll think about it Thank you!

05-12-2008, 02:20 PM	#5
slader99 Stock Join Date: Apr 2008 Location: canada Posts: 26	I use a similar type solution. If you have lots of metric hardware around find a long bolt, two matching nuts, turn the nuts onto the end of the bolt, and lock them together. If you find its still slipping you can destry the threads of your toyota SST with a flat head screw driver. Might save a trip to the store....

05-13-2008, 03:23 PM	#7
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	Looks like it was go or blow time. Nice job. It looks much worse than it is serge. Once you start cleaning it up. You'll see.