Ign Switch Signal for Elec. Fans

mkiiisupra · 09-17-2008, 03:20 AM

Trying to figure out where to wire in a ign switch signal for my perma-cool temperature switch so it will only turn on fans with the key in the ON posistion.

Looked around alot and cant really find where to wire into any help would be appreciated. Wiring diagrams have me scratching my head heh

btwilson86 · 09-17-2008, 02:49 PM

Well, I know on most vehicles windshield washer motors are only on when the key is in the on position (dunno about the supra). You could use a volt meter and test the voltage between the various wires there and a chassis ground to find one that's only powered when the key is on. Using a tap splice you could then run straight to what you need powered, as long as it is just a low amp signal.

If you need to draw current from this line, again use a tap splice and run a wire to the coil side of a relay of proper amperage. Run another wire from the other coil contact to a chassis ground. Then run another wire (with a fuse) from a 12V power source (battery or fuse box) to the contact side of the relay, and then a wire from the remaining contact to the power input on your fan switch. This way you draw very little power on the windshield washer motor circuit, but only allow the fans to work when the key is in the on position.

SilenceboneSupra · 03-13-2009, 05:00 PM

Sorry to bump this thread to but you can use a relay XD

09-17-2008, 03:20 AM	#1
mkiiisupra Lexus & 550's Join Date: Sep 2007 Location: Las Vegas, NV Posts: 570 Blog Entries: 1	Ign Switch Signal for Elec. Fans Trying to figure out where to wire in a ign switch signal for my perma-cool temperature switch so it will only turn on fans with the key in the ON posistion. Looked around alot and cant really find where to wire into any help would be appreciated. Wiring diagrams have me scratching my head heh __________________ 1990 Toyota Supra Turbo A/T ------------------------------------------------ Questions about oil? take a look http://www.supramania.com/aehaas/

09-17-2008, 02:49 PM	#2
btwilson86 Super Moderator Join Date: May 2007 Location: Billings, Montana Posts: 1,034	Well, I know on most vehicles windshield washer motors are only on when the key is in the on position (dunno about the supra). You could use a volt meter and test the voltage between the various wires there and a chassis ground to find one that's only powered when the key is on. Using a tap splice you could then run straight to what you need powered, as long as it is just a low amp signal. If you need to draw current from this line, again use a tap splice and run a wire to the coil side of a relay of proper amperage. Run another wire from the other coil contact to a chassis ground. Then run another wire (with a fuse) from a 12V power source (battery or fuse box) to the contact side of the relay, and then a wire from the remaining contact to the power input on your fan switch. This way you draw very little power on the windshield washer motor circuit, but only allow the fans to work when the key is in the on position. __________________ 1989 7MGTE R154 Targa Top White Package w/Blue Interior Driftmotion 57trim CT26, Upgraded Intercooler, 2.25" Hard Pipes, 3" Turbo Back Exhaust with Test Pipe, HKS VPC w/GM 3 bar MAP sensor, APEXi S-AFC, Walbro 255lph fuel pump, ProSport EVO Series Boost / Fuel Pressure / AFR gauges, Lotek a Pillar Gauge Pod, HKS Type 0 Turbo Timer, Eibach Lowering Springs, Tokico Illumina II TEMS struts, custom powder coated Motegi Racing TrakLite wheels

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Master Window Switch?	Supra_Nubus	MKIII Supra	2	04-09-2008 01:49 AM
No Signal to Fuel Injector	ithinkitwassumthini8	MKIII Supra	3	09-12-2006 06:35 AM
Faulty Headlight Switch... please help!	MusicNazi525	MKIII Supra	4	10-30-2005 12:31 AM

03-13-2009, 05:00 PM	#3
SilenceboneSupra 3" Exhaust Join Date: Oct 2007 Location: Aruba Posts: 113	Sorry to bump this thread to but you can use a relay XD