Bolt/ Nut specs???

dannydavi · 10-29-2009, 01:38 AM

hey umm i need some info for some lost bolts/ nuts :s unfortunately didnt keep good track of everything when taking my engine out

ok the things i need most is the specs on the bolt that hold the starter to the block/transmission area? the ones that go through the bellhousing, i mis placed mine and dont know what to look for when buying at this point and the TSRM doesnt help me in this department, also the nut on the starter that you fasten the hot lead with i have lost, these things would be easy to find out if the starter was easy to get to, and I'd rather not buy and try a bunch of bolts, thanks in advance for any info/charts/etc.. or link to spot in TSRM where it might tell me this info

cre · 10-29-2009, 08:14 PM

http://www.tampabaysupras.com/files/...eFasteners.pdf

dannydavi · 10-29-2009, 11:47 PM

wow priceless chart CRE, thanks for your response and your information, it is greatly appreciated, I actually called the toyota dealer earlier today and found out the 10mm x 1.25 measurements but they did not have the length.. but i will save this link for future use for sure, thanks again.

ddmcse · 10-31-2009, 01:58 AM

i have a bag of bolts from my conversion . i'll look in tomorrow

dannydavi · 11-02-2009, 05:54 AM

ok so nut that holds wire onto starter is a 8mm x 1.25 pitch and bolt that holds starter onto bellhousing is 10mm x 1.25 pitch and the length was about 2 inches.

10-29-2009, 01:38 AM	#1
dannydavi 12psi boost Join Date: Mar 2007 Location: Sacramento, Ca Posts: 373	Bolt/ Nut specs??? hey umm i need some info for some lost bolts/ nuts :s unfortunately didnt keep good track of everything when taking my engine out ok the things i need most is the specs on the bolt that hold the starter to the block/transmission area? the ones that go through the bellhousing, i mis placed mine and dont know what to look for when buying at this point and the TSRM doesnt help me in this department, also the nut on the starter that you fasten the hot lead with i have lost, these things would be easy to find out if the starter was easy to get to, and I'd rather not buy and try a bunch of bolts, thanks in advance for any info/charts/etc.. or link to spot in TSRM where it might tell me this info __________________ '86.5 Supra - A/T - N/A - JDM Useful Sites: ToyoDIY.com ToyotaPart.com MKIIITSRM

10-29-2009, 11:47 PM	#3
dannydavi 12psi boost Join Date: Mar 2007 Location: Sacramento, Ca Posts: 373	wow priceless chart CRE, thanks for your response and your information, it is greatly appreciated, I actually called the toyota dealer earlier today and found out the 10mm x 1.25 measurements but they did not have the length.. but i will save this link for future use for sure, thanks again. __________________ '86.5 Supra - A/T - N/A - JDM Useful Sites: ToyoDIY.com ToyotaPart.com MKIIITSRM

10-31-2009, 01:58 AM	#4
ddmcse 500whp yet? Join Date: Jun 2005 Location: CT U.S.A. Posts: 966	i have a bag of bolts from my conversion . i'll look in tomorrow __________________ 300+ RW HP Dyno run, jdm,mod turbo,3"exh,electfan,greddyboost Blown HeadGasket info My Supra KiXGaS

11-02-2009, 05:54 AM	#5
dannydavi 12psi boost Join Date: Mar 2007 Location: Sacramento, Ca Posts: 373	ok so nut that holds wire onto starter is a 8mm x 1.25 pitch and bolt that holds starter onto bellhousing is 10mm x 1.25 pitch and the length was about 2 inches. __________________ '86.5 Supra - A/T - N/A - JDM Useful Sites: ToyoDIY.com ToyotaPart.com MKIIITSRM

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
A Little Story about a crank bolt	abhattan	MKIII Supra	17	03-28-2013 01:06 AM
Help on head bolt torque specs	omar	MKIII Supra	3	07-29-2009 11:35 AM
stripped rear end bolt	87 Supra	MKIII Supra	5	10-16-2007 02:40 PM
Broken Bolt	scruffboy	Non-Generation Specific Questions	6	10-31-2006 01:33 PM
head bolt specs	skunk	MKIII Supra	3	07-13-2005 07:29 PM

10-29-2009, 08:14 PM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	http://www.tampabaysupras.com/files/...eFasteners.pdf