setting cam position sensor?

mattromey · 11-13-2009, 08:31 PM

i just got my head back from the shop and reinstalled the cams and cant remember how to set the cam position sensor.

Thanks
Matt

cre · 11-13-2009, 10:42 PM

Make sure the cam gears and the crank pulley are aligned at 0°. Then:

http://www.cygnusx1.net/Supra/Librar...aspx?S=IG&P=19

Bill UK · 11-13-2009, 11:06 PM

Locate the CPS with the cam pulleys as sown below, assuming you have already re-installed the can belt with the crank pulley set at zero (# 1 piston at top dead centre) and cam pulleys as in photo. Line up the hole and notch as marked with the red arrow on the CPS and insert into the head. You may find when the gear engages with camshaft helical gear the CPS shaft will rotate, I removing mine a few times to double check it hadn’t moved before nipping up the adjusting bolt. Its also worth replacing the O ring Toyota part # 90099-14018

018

cre · 11-14-2009, 12:18 AM

Thanks for the correction Bill! It's been quite a while since I've dealt with this.

mattromey · 11-15-2009, 05:31 PM

Hey thanks a lot for the help you guys are awsome!

untweru · 11-18-2009, 06:45 PM

Hopefully this gets sticky'd. There seems to be some debate over WHERE the oil comes from. I'm here to settle this once and for all, as I am tired of replying over and over again to this simple problem that anyone can repair very easily.

First of all, many DOHC engines have spark plug well seals. This, however, is not the case on the 87-92 7M engine.

Please refer to my custom diagram. When it says (color, shape) that is what I'm talking about. Pretty straight forward.

11-13-2009, 08:31 PM	#1
mattromey Stock Join Date: Oct 2009 Location: portland oregon Posts: 12	setting cam position sensor? i just got my head back from the shop and reinstalled the cams and cant remember how to set the cam position sensor. Thanks Matt

11-13-2009, 10:42 PM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Make sure the cam gears and the crank pulley are aligned at 0°. Then: http://www.cygnusx1.net/Supra/Librar...aspx?S=IG&P=19 Last edited by cre; 11-14-2009 at 12:17 AM. Reason: deleted erroneous info

11-18-2009, 06:45 PM	#6
untweru Stock Join Date: Nov 2009 Location: Canada Posts: 1	Hopefully this gets sticky'd. There seems to be some debate over WHERE the oil comes from. I'm here to settle this once and for all, as I am tired of replying over and over again to this simple problem that anyone can repair very easily. First of all, many DOHC engines have spark plug well seals. This, however, is not the case on the 87-92 7M engine. Please refer to my custom diagram. When it says (color, shape) that is what I'm talking about. Pretty straight forward. __________________ Annonces immobilier entre particuliers maison \| Achat immobilier entre particuliers vente \| Annonces immobilier entre particuliers

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Cam Position Sensor	JMoses	MKIII Supra	4	08-19-2009 05:09 PM
can cam position sensor cause	88Tsupra	MKIII Supra	4	03-22-2007 01:25 AM
Cam position sensor and Knock sensor	Burn N' Up	MKIII Supra	1	11-23-2005 11:27 PM

11-13-2009, 11:06 PM	#3
Bill UK AEM EMS Join Date: Jul 2006 Location: UK Posts: 891	Locate the CPS with the cam pulleys as sown below, assuming you have already re-installed the can belt with the crank pulley set at zero (# 1 piston at top dead centre) and cam pulleys as in photo. Line up the hole and notch as marked with the red arrow on the CPS and insert into the head. You may find when the gear engages with camshaft helical gear the CPS shaft will rotate, I removing mine a few times to double check it hadn’t moved before nipping up the adjusting bolt. Its also worth replacing the O ring Toyota part # 90099-14018 018

11-14-2009, 12:18 AM	#4
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	Thanks for the correction Bill! It's been quite a while since I've dealt with this.

11-15-2009, 05:31 PM	#5
mattromey Stock Join Date: Oct 2009 Location: portland oregon Posts: 12	Hey thanks a lot for the help you guys are awsome!