|
|
01-31-2010, 03:31 PM
|
#1 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
 |
wiring harness
was thinking about dropping my 7m-ge into an 85 celica supra(mk2) will the wiring harness from a 5mge be acceptable?
im going to be using thew tranny and everything out of a complete mk3 so i will have all the parts...
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
02-02-2010, 09:56 PM
|
#2 |
|
12psi boost
Join Date: May 2006
Location: Athens, TX
Posts: 308
|
The wiring harness is going to be different. As for the transmission easiest way would be measure all of the relative parts like lengths and mounting positions and see if everything will fit. I know a 7MGE will fit I have seen MK2's with 1JZ's in them before and the 1JZ is a little longer due to the turbo manifold.
__________________
1987 supra NA 5 speed 1JZGTE swap Tokico Illumina 2 and Eibach springs Tokico pillow blocks Suspension Techniques front and rear sway bar HKS super dragger cat-back exhaust plus test pipe Greddy Profec B spec 2 boost controller HKS type 1 turbo timer Supra sport solid steel drive shaft Walboro 255 fuel pump JZA70 Front end mod 18" Volk Racing AV3 18x8.5 front 18x9.5 rear |
|
|
|
|
02-03-2010, 02:01 AM
|
#3 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
Im not asking about the tranny, im asking if the wiring harness from 5m is compatible for 7m
and if so what is considered The "wiring harness" what parts i gotta pull for the wiring harness...
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
|
02-03-2010, 03:00 AM
|
#4 |
|
12psi boost
Join Date: May 2006
Location: Athens, TX
Posts: 308
|
The engine harness is the harness that connects to the ECU under the dash. It runs up the firewall and through the passenger side of the firewall and goes into the dash where the Computer sits. This is the engine harness. You may have to use some of the harnesses and connectors from the rest of the body harnesses. Those I am not to sure of with what will work between the two different body styles.
__________________
1987 supra NA 5 speed 1JZGTE swap Tokico Illumina 2 and Eibach springs Tokico pillow blocks Suspension Techniques front and rear sway bar HKS super dragger cat-back exhaust plus test pipe Greddy Profec B spec 2 boost controller HKS type 1 turbo timer Supra sport solid steel drive shaft Walboro 255 fuel pump JZA70 Front end mod 18" Volk Racing AV3 18x8.5 front 18x9.5 rear |
|
|
|
|
02-04-2010, 01:25 AM
|
#5 |
|
Official hall monitor / search nazi - NO SOUP FOR YOU!
Join Date: Oct 2009
Location: Canada, BC
Posts: 837
|
so either way i should take as much as i can for wiring from ECU back...
thank you for the reply
__________________
1984 supra - 1uzfe - w58 - 4.10 - 1 piece aluminum shaft. |
|
|
|
|
02-04-2010, 03:41 AM
|
#6 |
 Toyota Racing Development Join Date: Apr 2007
Posts: 5,038
 |
I would definitely stick with the 7M's harness.
The MKII Supra has a longer engine bay than the Celica's, make sure it'll fit.
__________________
If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal.  Tip Jar --->  |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 89 toyota supra wiring harness! | lolSupra | Non-Generation Specific Questions | 0 | 09-05-2008 03:49 PM |
| 87 na wiring harness.. | 7Mpowered87 | MKIII Supra | 3 | 05-13-2008 05:01 AM |
| 87 Supra Wiring Harness | slader99 | MKIII Supra | 9 | 04-28-2008 12:14 AM |
Hybrid Mode
