Toyota Supra Forums! Join the Supra forum!

Toyota Supra Forums! Join the Supra forum! (http://www.toyota-supra.info/forums/)
-   MKIII Supra (http://www.toyota-supra.info/forums/mkiii-supra/)
-   -   Oilpan Removal???? (http://www.toyota-supra.info/forums/mkiii-supra/17336-oilpan-removal.html)

ReelBandit 07-05-2010 07:25 PM

Oilpan Removal????
 
Has anyone ever removed the oil pan with the motor still in the car? I've removed everything that the book says and then some. According to my manual it says to lift the motor "slightly". I've done that and more and still cant get enough room to bring the oil pan back enough to get it to drop..:(

cre 07-05-2010 08:18 PM

slightly = 8 - 12" IIRC

ReelBandit 07-05-2010 08:31 PM

Can it be done without removing the engine?

cre 07-05-2010 09:09 PM

takes allot more than 12" to remove the engine.... so, um, yeah. :p

batmmannn 07-05-2010 09:48 PM

Run a search
 
Lots on the web about this. People say you have to do a lot of work to get that off including dropping the crossmember, unhooking the exhaust, lift the engine, remove the drag link.....UNNNGHHHH!

wstanek 07-05-2010 09:51 PM

i was planing on doing my rod bearings from the bottom but we might have to change that plan... D=

ReelBandit 07-05-2010 10:08 PM

Well, so far, I\'ve all but removed my engine, its hanging partly out of the engine bay right now. The book made it sound like most others, but NOT in this case...

batmmannn 07-05-2010 10:23 PM

Might as well pull it
 
If you have it that far you might as well just pull it. I have seen pics of them pulled with radiator removed and the trans still attached. Do the rear main crank seal and clutch plate while you are there. Can you throw some pics up so we can see your progress?

http://www.toyota-supra.info/forums/...n-leaking.html

cre 07-05-2010 11:25 PM

Can't do the main bearings or rear main seal with the transmission attached.... for that pull the engine.

Pulling the pan with the engine in the car isn't hard (been there done that). Personally, I'd recommend just pulling it, but I've had it off with the engine in the car and the wire harness all still connected. I have no idea what your problem is; you've just got to get the front of the engine elevated a dozen inches or so (I think it was closer to 8") and you don't even need to pull any cross members. Is your engine swinging forward as you lift it? Do you have a leveler?

ReelBandit 07-05-2010 11:33 PM

Yes I have a leveler. It just seemed no matter what I tried I still lacked a 1/2" of clearance to get the pan off.( with the tranny attached) Doesn't really matter now that I've pulled the motor partially out. I forgot to bring my camera today or I would upload pics. Gunna call it a day for now. I will be back on it after work tomorrow. Can the oil pump be rebuilt???? Thanks for all the input!


All times are GMT. The time now is 01:33 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.


1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87