7MGE Throttle Body

Mar1 · 12-04-2010, 08:20 AM

Hi all, I'm from Kuwait and need an advice. I have a 1991 Toyota Crown that uses a 7MGE engine. I need a throttle body for it. the part number of the throttle body is 22210-42350

My question is, can I use any 7MGE throttle body for it? from a Cressida or Supra?

thanks

cre · 12-04-2010, 11:10 AM

The upper intake of the 7M-GE from the Supra and the Cressida are quite different. Unfortunately, I no longer have access to any interchange databases to look it up for you. I'm pretty sure the Cressida throttle body will fit but I do not know if the Supra's will.

Looking at the published parts catalog the Supra's will not work... or at least Toyota says it was only used in the Supra. 22210-42310 for the A/T and 22210-42300 for the M/T.

Mar1 · 12-05-2010, 05:31 AM

Thank you for your reply, I just check toyodiy and below are my Crown Throttle body and the US Cressida one. will the Cressida one fit my Crown?

The gasket on the Cressida one looks different (#22271) while the Supra one looks nearly the same ! does this diagram help?

Crown Throttle body;

Cressida Throttle Body;

SUPRA Throttle Body;

cre · 12-05-2010, 07:48 AM

You can't rely on the technical drawings from a parts catalog for ush info.... BUT, seeing that it looks like the throttle body for the Crown is most similar to the Supra's TB and not the Cressida.... does the Crown have the ACIS system? Do you have a picture of your engine with the intake all installed and present?

Mar1 · 12-05-2010, 10:14 AM

This is the Crown engine bay;

btwilson86 · 12-05-2010, 03:37 PM

The intake system looks very similar to a Supra. In the technical drawings, it looked like a few vacuum ports were slightly different, not sure if the drawings are entirely accurate or if those differences would matter. Overall, I think it looks like a Supra TB would probably work

12-04-2010, 08:20 AM	#1
Mar1 Stock Join Date: Dec 2010 Location: Kuwait Posts: 8	7MGE Throttle Body Hi all, I'm from Kuwait and need an advice. I have a 1991 Toyota Crown that uses a 7MGE engine. I need a throttle body for it. the part number of the throttle body is 22210-42350 My question is, can I use any 7MGE throttle body for it? from a Cressida or Supra? thanks

12-05-2010, 05:31 AM	#3
Mar1 Stock Join Date: Dec 2010 Location: Kuwait Posts: 8	Thank you for your reply, I just check toyodiy and below are my Crown Throttle body and the US Cressida one. will the Cressida one fit my Crown? The gasket on the Cressida one looks different (#22271) while the Supra one looks nearly the same ! does this diagram help? Crown Throttle body; Cressida Throttle Body; SUPRA Throttle Body; Last edited by Mar1; 12-05-2010 at 05:39 AM.

12-05-2010, 07:48 AM	#4
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	You can't rely on the technical drawings from a parts catalog for ush info.... BUT, seeing that it looks like the throttle body for the Crown is most similar to the Supra's TB and not the Cressida.... does the Crown have the ACIS system? Do you have a picture of your engine with the intake all installed and present? __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

12-05-2010, 03:37 PM	#6
btwilson86 Super Moderator Join Date: May 2007 Location: Billings, Montana Posts: 1,034	The intake system looks very similar to a Supra. In the technical drawings, it looked like a few vacuum ports were slightly different, not sure if the drawings are entirely accurate or if those differences would matter. Overall, I think it looks like a Supra TB would probably work __________________ 1989 7MGTE R154 Targa Top White Package w/Blue Interior Driftmotion 57trim CT26, Upgraded Intercooler, 2.25" Hard Pipes, 3" Turbo Back Exhaust with Test Pipe, HKS VPC w/GM 3 bar MAP sensor, APEXi S-AFC, Walbro 255lph fuel pump, ProSport EVO Series Boost / Fuel Pressure / AFR gauges, Lotek a Pillar Gauge Pod, HKS Type 0 Turbo Timer, Eibach Lowering Springs, Tokico Illumina II TEMS struts, custom powder coated Motegi Racing TrakLite wheels

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
7gmte throttle body swap	vbryanv	MKIII Supra	10	05-09-2010 10:01 PM
Jdm Throttle Body	Luvs2slide	MKIII Supra	1	07-24-2006 07:15 AM
throttle body	87supraguy	MKIII Supra	0	02-17-2006 02:40 AM
throttle body	boogum7	MKIII Supra	5	12-21-2005 03:01 PM
mk4 throttle body on my 7mgte??	boner1115	MKIII Supra	1	11-05-2005 12:57 AM

12-04-2010, 11:10 AM	#2
cre Toyota Racing Development Join Date: Apr 2007 Posts: 5,038	The upper intake of the 7M-GE from the Supra and the Cressida are quite different. Unfortunately, I no longer have access to any interchange databases to look it up for you. I'm pretty sure the Cressida throttle body will fit but I do not know if the Supra's will. Looking at the published parts catalog the Supra's will not work... or at least Toyota says it was only used in the Supra. 22210-42310 for the A/T and 22210-42300 for the M/T. __________________ If something breaks or you need to contact a member of the administration please post HERE. Unless it's a private or administration matter please post it on the forum. It benefits no one else if car related questions aren't posted for future users and takes away from the time I'm able to spend helping on the rest of the forum. If you're so inclined I'm always more than happy to accept tips via PayPal. Tip Jar --->

12-05-2010, 10:14 AM	#5
Mar1 Stock Join Date: Dec 2010 Location: Kuwait Posts: 8	This is the Crown engine bay;