What kinda boost can I pull off premium?

rnoswal · 09-25-2005, 06:03 AM

Well I had a set of Wiseco domed pistons that had 25 cc domes. The head was milled so that the chambers were around 65 cc's. Giving a couple of cc's for the head gasket. I had close to 42 cc chambers. That put the compression right at 14 to one. I also had the timing set to 35 degrees total advance at 4000 rpm. I usually ran it to 7500 rpms before letting off. I had dual Dellorto carbs and that was a fun dirt track car to run. I wish I had the carb set for the Supra, 3 side draft carbs!!! Oh yeah. I had to sell the Celica though, they dropped the class at the end of last year. I sure do miss it.

Russ

intense 7MGTE · 09-26-2005, 05:59 PM

In order to run 30psi of boost you will need a bigger turbo first of all. The stock CT26 can only push out 15psi and at that point it is just blowing hot air. Secondly you will need a stronge top and bottom end wjich you have. Then you will need a tuning computer like a VPC2, a SAFC or better yet a EMS from AEM. Then you will need to run at least 100 octane to keep the motor from blowing sky high. 91-93 pump gas just will not cut it.

WiseAssJester · 09-27-2005, 12:21 AM

At what altitude? Tempuratures?

I appreciate the input, but lack only forced induction experience. I've built other beasts a'fore.

Thanks matey.

20 or 25 considered safe?

Isphius · 03-16-2006, 09:14 PM

and what is the best way to lower compression? wouldnt a thicker gasket be weaker? the only thing i can think of is shorter pistons and/or con rods, but where can you get those?

Isphius · 04-08-2006, 03:49 AM

Has anyone ever but a delorto or webber carb set up on a supra? youd only need 255 cfms for 6k rpms and at 80 % volumetric effciency. Maybe more or less. Youd just have to make your own manifold for it. I would only do that if i had an expensive fuel injection problem thou, like a fried coil or ecu. And you would also need a vaccum advance distributor or some kind of controler for the electric one

09-26-2005, 05:59 PM	#2
intense 7MGTE Stock Join Date: Jul 2005 Posts: 20	30psi and octane In order to run 30psi of boost you will need a bigger turbo first of all. The stock CT26 can only push out 15psi and at that point it is just blowing hot air. Secondly you will need a stronge top and bottom end wjich you have. Then you will need a tuning computer like a VPC2, a SAFC or better yet a EMS from AEM. Then you will need to run at least 100 octane to keep the motor from blowing sky high. 91-93 pump gas just will not cut it.

03-16-2006, 09:14 PM	#4
Isphius 500whp yet? Join Date: Nov 2005 Location: Long branch, NJ Posts: 1,006	and what is the best way to lower compression? wouldnt a thicker gasket be weaker? the only thing i can think of is shorter pistons and/or con rods, but where can you get those? __________________ Yay the supra assistant is gone!!! WEEE!!

04-08-2006, 03:49 AM	#5
Isphius 500whp yet? Join Date: Nov 2005 Location: Long branch, NJ Posts: 1,006	Has anyone ever but a delorto or webber carb set up on a supra? youd only need 255 cfms for 6k rpms and at 80 % volumetric effciency. Maybe more or less. Youd just have to make your own manifold for it. I would only do that if i had an expensive fuel injection problem thou, like a fried coil or ecu. And you would also need a vaccum advance distributor or some kind of controler for the electric one __________________ Yay the supra assistant is gone!!! WEEE!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
low boost psi, wtf	supradad86_5	MKIII Supra	4	02-09-2014 02:05 AM
wont hold boost	Supraman	MKIII Supra	12	04-19-2007 04:52 AM
issue w/ boost spikes? i think?	NOTORIOUS VR	Non-Generation Specific Questions	17	01-17-2007 08:35 PM
Boost issue.. Kinda...	2JZEFINI-17	MKIII Supra	1	11-12-2006 02:54 PM
No boost in neutral but boost in gear!	edgardo	MKIII Supra	5	10-09-2004 04:01 AM

09-25-2005, 06:03 AM	#1
rnoswal Lexus & 550's Join Date: Apr 2005 Location: Bossier City LA Posts: 556	Well I had a set of Wiseco domed pistons that had 25 cc domes. The head was milled so that the chambers were around 65 cc's. Giving a couple of cc's for the head gasket. I had close to 42 cc chambers. That put the compression right at 14 to one. I also had the timing set to 35 degrees total advance at 4000 rpm. I usually ran it to 7500 rpms before letting off. I had dual Dellorto carbs and that was a fun dirt track car to run. I wish I had the carb set for the Supra, 3 side draft carbs!!! Oh yeah. I had to sell the Celica though, they dropped the class at the end of last year. I sure do miss it. Russ

09-27-2005, 12:21 AM	#3
WiseAssJester 3" Exhaust Join Date: Sep 2005 Location: Reno Posts: 77	At what altitude? Tempuratures? I appreciate the input, but lack only forced induction experience. I've built other beasts a'fore. Thanks matey. 20 or 25 considered safe?