Fuzzy logic boost controller... HELP.

smurfmods · 10-06-2005, 10:35 AM

Purchased a fuzzy logic boost controller... with no instructions. Can anyone help?

Here is the info on it. The litte control module says FBC (fuzzy boost controller) Made by Autolook Motor Sports. It has a computer box with a bunch of wires hooked up to it. A control module on a black wire and a bunch of hoses with a boost controller at the end.

Anything would help. Even instructions for a competing brand.

Thanks!!

smurfmods · 10-06-2005, 10:19 PM

Anyone ever even used one of these??

joel w · 10-06-2005, 10:43 PM

there is no information on google about a company named autolook motorsports or auto look boost controllers that i can find in any combination of words? so no sorry

smurfmods · 10-07-2005, 12:41 AM

Yeah, I tried google too. I can't find instructions for any other makers fuzzy controllers either.

May be out of luck.

joel w · 10-07-2005, 01:01 AM

is it just the module controller box only or do you have the vac solinoids also?

smurfmods · 10-07-2005, 06:22 PM

Not sure what a VAC selenoid is... may not have them. Is that going to make a difference? Do I have to have them?

There is a retangular box with some vac hose fittings. Looks similar to a manual box controller.

joel w · 10-07-2005, 09:38 PM

[QUOTE=smurfmods]Not sure what a VAC selenoid is... may not have them. Is that going to make a difference? Do I have to have them?

ya my bad, i misread you, it sounds like its complete setup. may have to open it to determin what wires do what? got to be some info on net somewhere? where did you get it?

i found this for an hks fuzzy controller? give you some idea
Install
•12-volt ignition power
•Chassis ground
•Input vacuum line from pressurized side of turbo to port 2 on stepping motor
•Output vacuum line from port 3 on stepping motor to wastegate
•Manifold pressure vacuum reference from intake manifold to port 1 on stepping motor
•Only the EVC Pro will require these additional wires to be run to the ECU:
•Speed sensor signal
•Tachometer rpm signal
•Throttle position signal

yours is probably similar but cant help much more,, here is that page i was looking at http://www.superstreetonline.com/tec...83/index4.html

smurfmods · 10-08-2005, 09:39 AM

I will try to post a picture of the complete setup today...

After taking a close look at the wires (only 6 or 7 long wires) and vac hoses I believe I may be able to get a start on figuring this thing out. With some help from everyone here I think we can do this.

That list does help a little. Gives me an area to start looking.

10-06-2005, 10:35 AM	#1
smurfmods Stock Join Date: Oct 2005 Posts: 5	Fuzzy logic boost controller... HELP. Purchased a fuzzy logic boost controller... with no instructions. Can anyone help? Here is the info on it. The litte control module says FBC (fuzzy boost controller) Made by Autolook Motor Sports. It has a computer box with a bunch of wires hooked up to it. A control module on a black wire and a bunch of hoses with a boost controller at the end. Anything would help. Even instructions for a competing brand. Thanks!!

10-06-2005, 10:19 PM	#2
smurfmods Stock Join Date: Oct 2005 Posts: 5	Fuzzy logic Anyone ever even used one of these??

10-07-2005, 12:41 AM	#4
smurfmods Stock Join Date: Oct 2005 Posts: 5	Out of luck Yeah, I tried google too. I can't find instructions for any other makers fuzzy controllers either. May be out of luck.

10-07-2005, 06:22 PM	#6
smurfmods Stock Join Date: Oct 2005 Posts: 5	hmmm Not sure what a VAC selenoid is... may not have them. Is that going to make a difference? Do I have to have them? There is a retangular box with some vac hose fittings. Looks similar to a manual box controller.

10-07-2005, 09:38 PM	#7
joel w Lexus & 550's Join Date: Aug 2005 Location: In the shadows Posts: 506	[QUOTE=smurfmods]Not sure what a VAC selenoid is... may not have them. Is that going to make a difference? Do I have to have them? ya my bad, i misread you, it sounds like its complete setup. may have to open it to determin what wires do what? got to be some info on net somewhere? where did you get it? i found this for an hks fuzzy controller? give you some idea Install •12-volt ignition power •Chassis ground •Input vacuum line from pressurized side of turbo to port 2 on stepping motor •Output vacuum line from port 3 on stepping motor to wastegate •Manifold pressure vacuum reference from intake manifold to port 1 on stepping motor •Only the EVC Pro will require these additional wires to be run to the ECU: •Speed sensor signal •Tachometer rpm signal •Throttle position signal yours is probably similar but cant help much more,, here is that page i was looking at http://www.superstreetonline.com/tec...83/index4.html Last edited by joel williams; 10-07-2005 at 09:52 PM.

10-06-2005, 10:43 PM	#3
joel w Lexus & 550's Join Date: Aug 2005 Location: In the shadows Posts: 506	there is no information on google about a company named autolook motorsports or auto look boost controllers that i can find in any combination of words? so no sorry

10-07-2005, 01:01 AM	#5
joel w Lexus & 550's Join Date: Aug 2005 Location: In the shadows Posts: 506	is it just the module controller box only or do you have the vac solinoids also?

10-08-2005, 09:39 AM	#8
smurfmods Stock Join Date: Oct 2005 Posts: 5	Fuzzy logic I will try to post a picture of the complete setup today... After taking a close look at the wires (only 6 or 7 long wires) and vac hoses I believe I may be able to get a start on figuring this thing out. With some help from everyone here I think we can do this. That list does help a little. Gives me an area to start looking.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Manual Boost Controller and Turbo timmer question	ethan12510	MKIII Supra	5	02-20-2008 10:54 PM
manual boost controller!!!!!!!	justin1642	MKIII Supra	6	01-16-2007 10:01 PM
ANY ONE EVERY USE A Apexi Boost Controller	donutking	MKIII Supra	1	10-07-2005 01:58 PM
installing manual boost controller 1989??	hamburgler	MKIII Supra	4	07-13-2005 12:55 PM