this one has me stumped

rnoswal · 01-03-2007, 12:35 PM

Hard to say for sure. They are cars that have a valve clearance that has to be adjusted by replacing shims. That will cause a ticking noise if the gap is too large. One way to check for wrist pin noise is to pull a sparkplug wire on the suspected cylinder and listen to see if the noise goes away. The other area is piston slap. If the cylinders are really worn they can make a noise, but I think the only way to check it is a leak down test or pull the head and actually measure the cylinder, which is a severe pain in the ass.

It does sound like your measurements are out, but if it still runs without missing then it should be OK. You might have a LOT of carbon build up in the intake/exhaust and top of the piston which will cause quite a raise in compression Then the fuel might detonate because of not enough octane at the new timing mark you reset it to.

The oil pressures sound about right, but you might want to change the oil and filter and put a higher viscosity oil in to see if it moves up any. Let us know how the noise goes and if you make any progress.

Russ

supradaddy0803 · 01-04-2007, 01:23 AM

yes the head is a pain in the behind I had a 86.5 and rebuilt the whole motor and the head was the funnest part to pull out from under the hood needed me and someone else on the other side to lift it. The sound is kind of like the when a motor deisels you hear that clack noise it is kind of like that it is a better way to describe the noise all together. The shop manual has no trouble shooting for a knock so I am kind of stuck. As for oil I am using Quaker state high mile 20w- 50 because of the fact it has leaking valve guides and it has 150000 miles on it so the oil is decent not like royal purple or anything or racing oil. my 86.5 never really had high opil pressure or anything. I just need to know if this is going to get expensive again like my 86.5 because I might have enough money to buy a different motor like a 1JZGTE 5spd just trying to make it cost effective so I can delegate funds towards it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
stumped :(	coolguy5602005	MKIII Supra	5	06-03-2008 10:29 PM
1988 7MGE Misfire - Stumped!	excaliburdj	MKIII Supra	21	04-16-2008 04:56 AM
No Spark, Stumped!	supraman8188	Non-Generation Specific Questions	0	04-13-2008 04:50 PM
89 Turbo....STUMPED.. >.<	RspecMKiii	MKIII Supra	5	04-12-2008 11:10 AM
Toyota Dealer Is Stumped, Car Cuttsoff	SYKOKIDD	Non-Generation Specific Questions	0	12-08-2006 05:16 PM

01-03-2007, 12:35 PM	#1
rnoswal Lexus & 550's Join Date: Apr 2005 Location: Bossier City LA Posts: 556	Hard to say for sure. They are cars that have a valve clearance that has to be adjusted by replacing shims. That will cause a ticking noise if the gap is too large. One way to check for wrist pin noise is to pull a sparkplug wire on the suspected cylinder and listen to see if the noise goes away. The other area is piston slap. If the cylinders are really worn they can make a noise, but I think the only way to check it is a leak down test or pull the head and actually measure the cylinder, which is a severe pain in the ass. It does sound like your measurements are out, but if it still runs without missing then it should be OK. You might have a LOT of carbon build up in the intake/exhaust and top of the piston which will cause quite a raise in compression Then the fuel might detonate because of not enough octane at the new timing mark you reset it to. The oil pressures sound about right, but you might want to change the oil and filter and put a higher viscosity oil in to see if it moves up any. Let us know how the noise goes and if you make any progress. Russ

01-04-2007, 01:23 AM	#2
supradaddy0803 12psi boost Join Date: May 2006 Location: Athens, TX Posts: 308	yes the head is a pain in the behind I had a 86.5 and rebuilt the whole motor and the head was the funnest part to pull out from under the hood needed me and someone else on the other side to lift it. The sound is kind of like the when a motor deisels you hear that clack noise it is kind of like that it is a better way to describe the noise all together. The shop manual has no trouble shooting for a knock so I am kind of stuck. As for oil I am using Quaker state high mile 20w- 50 because of the fact it has leaking valve guides and it has 150000 miles on it so the oil is decent not like royal purple or anything or racing oil. my 86.5 never really had high opil pressure or anything. I just need to know if this is going to get expensive again like my 86.5 because I might have enough money to buy a different motor like a 1JZGTE 5spd just trying to make it cost effective so I can delegate funds towards it.