ball joints

Jjona5 · 02-26-2007, 01:33 AM

What is the process on changing the ball joints on an 88 supra? Do you change the whole A arm or can it be pressed in and out?

supradaddy0803 · 02-26-2007, 02:54 AM

It is actually easy you basically look on the back of the spindle and you will see a castlated nut on the bottom and the top the one on the bottom is the one you are looking for. Pull the cotter pin out and loosen the nut heres the fun part pop the stud out of the spindle and remove the three bolts from the lower A arm and the whole assembly slides out. I looked all over when I got ready to do mine they dont even actually sell ball joint to be pressed out the assembly you buy is the one you need.

mrnickleye · 02-26-2007, 05:10 AM

http://www.cygnusx1.net/Supra/Librar...tion=FA&Page=1

TSRM is your Supra Bible. Study it for the good word !!

Jjona5 · 02-26-2007, 06:36 AM

So the upper balljoint is just a 300-400 dollar entire assembly then...sigh.

mr.w · 02-27-2007, 03:12 AM

It was pretty easy to do, I only paid $75 for my ball joint at autozone. Definatley didn't cost $300-$400 dollars.

Jjona5 · 02-27-2007, 03:19 AM

Were you changing the upper or the lower? The lower ball joints look like they can be bought by themselves...the upper looks like it has to be bought as an entire assembly

02-26-2007, 01:33 AM	#1
Jjona5 Intake Join Date: Feb 2007 Location: Highlands, TX Posts: 47	ball joints What is the process on changing the ball joints on an 88 supra? Do you change the whole A arm or can it be pressed in and out?

02-26-2007, 05:10 AM	#3
mrnickleye 1000whp postwhore Join Date: Jun 2005 Location: Mojave Desert, Calif. Posts: 1,705	See This in TSRM. http://www.cygnusx1.net/Supra/Librar...tion=FA&Page=1 TSRM is your Supra Bible. Study it for the good word !! __________________ Had a Red 1989 N/A. Automatic. Sports Pkg. w/wing. TEMS, and some nice MODS. Sold to a friend 10/08/08.

02-26-2007, 06:36 AM	#4
Jjona5 Intake Join Date: Feb 2007 Location: Highlands, TX Posts: 47	hmm So the upper balljoint is just a 300-400 dollar entire assembly then...sigh.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Lower Ball Joints - Checking here first	Grandavi	MKIII Supra	3	09-20-2008 04:04 AM
power steering problem	3.0trd	MKIII Supra	12	06-24-2008 01:17 PM
Tie Rods & Ball Joints	mrnickleye	MKIII FAQ	1	03-10-2007 04:50 AM
Tie Rod End and Ball Joints!!	KrnSupra2307	MKIII Supra	6	02-27-2007 11:01 PM

02-26-2007, 02:54 AM	#2
supradaddy0803 12psi boost Join Date: May 2006 Location: Athens, TX Posts: 308	It is actually easy you basically look on the back of the spindle and you will see a castlated nut on the bottom and the top the one on the bottom is the one you are looking for. Pull the cotter pin out and loosen the nut heres the fun part pop the stud out of the spindle and remove the three bolts from the lower A arm and the whole assembly slides out. I looked all over when I got ready to do mine they dont even actually sell ball joint to be pressed out the assembly you buy is the one you need.

02-27-2007, 03:12 AM	#5
mr.w 3" Exhaust Join Date: Nov 2006 Location: Cleveland, Ohio Posts: 70	It was pretty easy to do, I only paid $75 for my ball joint at autozone. Definatley didn't cost $300-$400 dollars.

02-27-2007, 03:19 AM	#6
Jjona5 Intake Join Date: Feb 2007 Location: Highlands, TX Posts: 47	Were you changing the upper or the lower? The lower ball joints look like they can be bought by themselves...the upper looks like it has to be bought as an entire assembly