crank shaft pulley puller

supramacist · 04-15-2007, 09:53 PM

The tape and the prybar work just fine.

I just can't get the crank bolt to budge. So I'm going to soak it in more pb blaster and try again later. Nothing worth doing is ever easy.

j3pz · 04-16-2007, 04:16 AM

good luck with that bolt

supramacist · 04-16-2007, 05:45 AM

Clearly I'm going to need it.

Thanks.

supramacist · 04-17-2007, 05:09 PM

Alright guys. I bought a 17 inch breaker bar and a deep welled 1/2 inch 19mm socket. I can not budge this damn bolt. Should I try tapping on it with a hammer before breaking it??? I'm running out of options. I'll have my head tomorrow and I need to get this bitch broken so I can replace my timing belt AAAAAAAAAAAAAAAAAAAAAAArgh.

IHateHacks · 04-17-2007, 05:11 PM

Put a pipe on the end of the 17in breaker bar. A nice 3 footer will do the trick.

Glad to hear you stopped the crank from moving.

supramacist · 04-17-2007, 05:22 PM

I just knew I was going to pop this thing like a zit last night. I tried extending it. Either the pry bar slips and jacks up my flywheel or it sticks and I just can't pop it. Hello I'm not a weak dude either.

IHateHacks · 04-17-2007, 05:32 PM

Are you yourself holding the prybar AND trying to break it loose? Or do you have a helper?

Have a helper hold the prybar, get a long ass pipe and you should be straight.

Never said you were weak.

04-15-2007, 09:53 PM	#1
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	The tape and the prybar work just fine. I just can't get the crank bolt to budge. So I'm going to soak it in more pb blaster and try again later. Nothing worth doing is ever easy. Last edited by supramacist; 04-16-2007 at 05:44 AM.

04-16-2007, 04:16 AM	#2
j3pz 500whp yet? Join Date: Nov 2005 Location: Mechanicsville, MD, US of A, 20659 Posts: 1,060	good luck with that bolt __________________ 88 N/A w/ 5spd - stock - not running, bhg 87 turbo/targa w/ 5spd- fidanza light weight flywheel, new oem slave cylinder, apexi air filter, no ac and no heat

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
1980 Supra Crank Pulley (Harmonic Balancer)	steve6163	Non-Generation Specific Questions	7	06-18-2010 01:47 AM
Crank Pulley Removal	go.stfu	MKIII Supra	4	07-12-2007 11:16 PM
question on removing crank shaft	kidsusukigsxr	Non-Generation Specific Questions	12	07-07-2007 03:49 PM
Unorthodox Supra Ultra S - Lightened Crank Pulleys	Kuban	MKIII Supra	1	03-13-2007 09:39 PM
Crank shaft pulley..	MA70_858	Non-Generation Specific Questions	3	07-28-2006 04:47 PM

04-16-2007, 05:45 AM	#3
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	Clearly I'm going to need it. Thanks.

04-17-2007, 05:09 PM	#4
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	Alright guys. I bought a 17 inch breaker bar and a deep welled 1/2 inch 19mm socket. I can not budge this damn bolt. Should I try tapping on it with a hammer before breaking it??? I'm running out of options. I'll have my head tomorrow and I need to get this bitch broken so I can replace my timing belt AAAAAAAAAAAAAAAAAAAAAAArgh.

04-17-2007, 05:11 PM	#5
IHateHacks 20psi boost Join Date: May 2006 Location: New Haven/Hamden Posts: 793	Put a pipe on the end of the 17in breaker bar. A nice 3 footer will do the trick. Glad to hear you stopped the crank from moving.

04-17-2007, 05:22 PM	#6
supramacist 1000whp postwhore Join Date: Apr 2007 Location: Escape from the Prison Planet Posts: 1,356	I just knew I was going to pop this thing like a zit last night. I tried extending it. Either the pry bar slips and jacks up my flywheel or it sticks and I just can't pop it. Hello I'm not a weak dude either.

04-17-2007, 05:32 PM	#7
IHateHacks 20psi boost Join Date: May 2006 Location: New Haven/Hamden Posts: 793	Are you yourself holding the prybar AND trying to break it loose? Or do you have a helper? Have a helper hold the prybar, get a long ass pipe and you should be straight. Never said you were weak.