07-04-2006, 08:34 PM | #1 |
3" Exhaust
Join Date: Jun 2006
Location: houston
Posts: 160
|
Oil Is Leaking I Have Pics!! Need Help!!
i need help my oil is leaking but not much, but it needs to fixed and i need to know where it could be leaking from.
circled in red is the oil spot on the ground circled in red again is where i think it could be leaking from. my car is an 88 N/A, no mods. please help thankyou
__________________
Rollin in a 98, flippin 94's |
07-04-2006, 08:47 PM | #2 |
3" Exhaust
Join Date: Aug 2005
Location: Colorado
Posts: 98
|
Oil pan gasket? Could be!
__________________
4" Turbo back/maft-pro powered/70mm TC turbo/JE Built forged motor |
07-04-2006, 09:00 PM | #3 |
3" Exhaust
Join Date: Jun 2006
Location: houston
Posts: 160
|
lol to tell you the truth i didn't know an oil pan had a gasket how much would it be to replace it? all together
__________________
Rollin in a 98, flippin 94's Last edited by Ahmad88; 07-04-2006 at 09:04 PM. |
07-04-2006, 09:29 PM | #4 |
12psi boost
Join Date: May 2006
Location: Oregon
Posts: 376
|
Thats right below your oil filter, Im gonna bet your pan gasket is fine and what your seeing is just the build up before it drips off the edge. Make sure your filter is screwed on tight. Take a rag and wipe the area dry, then run the car and look for the leak.
I thought your car was siezed?
__________________
____________ Eagles may soar, but weezl's never get sucked into jet engines! |
07-04-2006, 10:01 PM | #5 |
3" Exhaust
Join Date: Jun 2006
Location: houston
Posts: 160
|
no i later found out that its jsut a starter, i got some people to listen to it and they have friends that had the same problem and they say its the starter, which is wut everyone i know is sayin, and the car wont start.sometimes it almost cranks over but it doesnt start up. i found the starter but cant unbolt it from the hood area and i need to wait for my brother to get home to help me jack it up to see if i can get it from the underneath but im kinda scared cuz i always have feelin its gonna roll off the jacks and slam on me.
__________________
Rollin in a 98, flippin 94's |
07-05-2006, 05:58 PM | #6 |
20psi boost
Join Date: May 2006
Location: New Haven/Hamden
Posts: 793
|
If you are going to replace the oil pan gasket make sure you use Seal packing part # 08826-00080 from any toyota dealer. The gasket itself is only 7 bucks at any cheapass autostore, but take a look under the car.... you see that big suspension crossmember? Yea that has to come down along with the steering rack, whole front suspension etc. It is defineitly do-able but it will be hard to say the least.
|
07-05-2006, 10:14 PM | #7 |
500whp yet?
Join Date: Aug 2005
Location: Plantation, Fl.
Posts: 1,052
|
My bet is that its the oil filter. The oil pan has a FIPG (form in place gasket). Go outside right now and check the oil level. I'm sure it's low. The engine will not tolerate low oil levels. So do the steps as follows.
1. Drain oil 2. Take off old oil filter (make sure the gasket is still on it) 3. Clean oil filter housing 4. Put drain plug back in 5. Put oil on new oil filter gasket 6. Put 5 quarts of oil in it 7. Start car for 30 seconds then turn off 8. Check oil level You should be good to go. If it still happens, take it to an oil changing shop and they'll look to see where it's leaking from for no charge. At least the place I work at will. If you didnt clean the oil filter housing, it would have a bad seal. All it needs is a little dirt to make a bad seal. |
07-06-2006, 08:23 AM | #8 |
3" Exhaust
Join Date: Jun 2006
Location: houston
Posts: 160
|
thx for the help guys but today im getting a new starter and a brake pads installed hopefuly, if my car turns on, i'll change the oil and do wut u said dcrusupra, thx for the help everyone.
P.S. in the first picture, that's the O2 sensor right? how do i remove it? just unscrew it or yank it out?
__________________
Rollin in a 98, flippin 94's Last edited by Ahmad88; 07-06-2006 at 08:26 AM. |
07-06-2006, 01:14 PM | #9 |
7M POWAH! ;)
Join Date: Jun 2004
Location: New Zealand
Posts: 2,312
|
ye i reckon oil filter too... i see a little bit of oil just to the right of it there so i think it's dropping down from there
02 sensor has 2 12mm nuts, you need to undo them to get the 02 off
__________________
Please use the forum to ask your questions as they will get replied to much faster than pming me Pics of my build. "Good girls are just bad girls that don't get caught" Do a diagnostic first! |
07-06-2006, 10:35 PM | #10 |
500whp yet?
Join Date: Aug 2005
Location: Plantation, Fl.
Posts: 1,052
|
And if you need the PN to an oil filter, its MO241. Its a mobil oil filter.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
post all pics and videos here! 56k warning: large pics | mnewxv | Show n Tell | 0 | 10-13-2008 07:49 PM |
pics of my new supra | brs86supra | MKIII Supra | 4 | 01-01-2007 09:02 PM |
Pics... | TxSpeedBoy | Non-Generation Specific Questions | 2 | 01-12-2006 10:56 PM |