Forum: MKIII Supra
04-17-2015, 11:35 AM
|
|
Replies: 13
Views: 7,729
I had rthe same issue.
I tried the following...
I had rthe same issue.
I tried the following which worked for me...
a) Check ALL Earthing points
b) Ignition timing needs to be correct or the engine wont start.
It takes time but its worth...
|
|
Forum: MKIII Supra
04-17-2015, 11:27 AM
|
|
Replies: 3
Views: 2,946
|
|
Forum: MKIII Supra
10-31-2014, 09:25 PM
|
|
Replies: 3
Views: 1,564
hi
I was actually looking on ebay to see what the price of a sheet of foam gasket costs.
Its not that expensive compared to buying it from Toyota.
I think Toyota do EACH side gasket for around...
|
|
Forum: MKIII Supra
10-27-2014, 02:04 PM
|
|
Replies: 3
Views: 1,564
Rear Brake Light seal
Can anyone help me please..
I need a pair of seals / gaskets for the rear brake light cluster.
The toyota part number is - 8156414610
Has anyone had any luck by making their own ???
...
|
|
Forum: MKIII Supra
04-13-2012, 10:07 AM
|
|
Replies: 2
Views: 3,051
cps issue
I found on my car even with the crank shaft pulley and cam shaft pulleys aligned up my car would not start correctly.
I played around with the CPS and still nothing.
I then discovered by using...
|
|
Forum: MKIII Supra
12-17-2011, 09:58 AM
|
|
Replies: 18
Views: 13,463
Hi
Hi Bill
i have checked my CPS and its not leaking at all. The gears are in good condition also.
I dont think i need to touch the CPS in anyway. After all it was working fine before the head...
|
|
Forum: MKIII Supra
12-16-2011, 11:09 AM
|
|
Replies: 18
Views: 13,463
hi
Hi there
I have followed all the guides that there are for the setup of the timing etc
I will just explain in detail what has been done so far with the alignments etc..
a) The crank shaft...
|
|
Forum: MKIII Supra
12-15-2011, 03:01 PM
|
|
Replies: 18
Views: 13,463
hi
Hi there
Just to recap on the situation regarding my cars timing etc...
If i followed the instructions in the guide ie crank shaft pulley at zero, cams aligned at the notches etc and the no...
|
|
Forum: MKIII Supra
12-11-2011, 08:13 PM
|
|
Replies: 1
Views: 1,771
CPS out by 180 degrees
Just a quick question with my car.
The thing with my car is that i have set the crank shaft pulley to zero mark and made sure that it is on TDC.
Cam shafts are aligned to the mark on the back...
|
|
Forum: MKIII Supra
12-11-2011, 08:06 PM
|
|
Replies: 12
Views: 4,247
hi
Just a quick question...... did you guys eventually sort the issue out ??
The thing with my car is that i have set the crank shaft pulley to zero mark and made sure that it is on TDC.
Cam...
|
|
Forum: MKIII Supra
10-09-2011, 02:21 PM
|
|
Replies: 18
Views: 13,463
hi
Hi there
I am still having some issues with my timing and due to that the car is idling eractly.
To explain what i have done:
a) Crank shaft aligned to the Zero Mark.
b) Intake and...
|
|
Forum: MKIII Supra
03-05-2011, 10:13 AM
|
|
Replies: 18
Views: 13,463
hi
Actually you are right about using the stick in cyclinder 1 method to check TDC, you could be looking at something that is 180 degrees out and that wont work will it.
So, using this stick method...
|
|
Forum: MKIII Supra
03-04-2011, 09:33 PM
|
|
Replies: 18
Views: 13,463
thanks bill..... your correct it should be at...
thanks bill..... your correct it should be at zero and NOT 10 degrees - my fault.... need booze brain slooooow
I normally use that method that you told me to find TDC, spark plug 1 out, insert...
|
|
Forum: MKIII Supra
03-04-2011, 09:28 PM
|
|
Replies: 18
Views: 13,463
hi
Hi, thanks for that information. I will try that over the weekend and fingers crossed it will be ok.
I have the haynes manual and other manuals too so if i get stuck i have some kind of reference...
|
|
Forum: MKIII Supra
03-04-2011, 09:05 PM
|
|
Replies: 18
Views: 13,463
hi
Hi Bill, Yes i read that also about the strobe light being applied to ignition lead 6.
The problem that i have is that the car starts but the idle is very rough. So, i need to recheck the ignition...
|
|
Forum: MKIII Supra
03-04-2011, 02:28 PM
|
|
Replies: 18
Views: 13,463
hi
Ah thats brilliant Bill. Thanks for your help. At least i can get my car done now over the weekend.
Thanks again.....
|
|
Forum: MKIII Supra
03-03-2011, 02:35 PM
|
|
Replies: 18
Views: 13,463
7M GTE ignition timing guide needed...
Hi there
i need some advice on the sequence that the ignition leads go.
Can anyone tell me what cyclinder the leads go from the ignition packs...?
example...
if looking at the coil packs...
|
