Forum: MKIII Supra
11-16-2007, 03:39 PM
|
|
Replies: 6
Views: 6,894
Thanks guys - Problem solved
I just kept topping off the radiator and after 4 times and 300 miles later, it is holding. But I was curious if any of this block and head sealer stuff works. Hope I never have to find out. Thanks...
|
|
Forum: MKIII Supra
11-13-2007, 09:55 PM
|
|
Replies: 6
Views: 6,894
Anyone ever try cracked block fixer like Irontite?
I just had a new head gasket installed and head rebuilt on my 1991 Supra turbo. Runs like a charm, lots of power, but coolant is slowly disappearing. Yes, whitish steam comes out the tailpipe when...
|
|
Forum: MKIII Supra
09-06-2007, 03:21 PM
|
|
Replies: 6
Views: 2,295
Thanks oowee623 Bell housing?
Thanks oowee623. If I get the 1jz with tranny (Auto), do I still have to do something about the bellhousing? I guess the drive shaft is still no problem, no? Thanks, I still am doing my homework....
|
|
Forum: MKIII Supra
09-05-2007, 08:15 PM
|
|
Replies: 6
Views: 2,295
1jz for 1991 Supra turbo/harness,motor mts issue?
Thanks for all the info in the previous thread. I think I understand a whole lot more about Supras and what can be done with them.
From that, I like the 1jz swap to my 1991 Supra Turbo idea. From...
|
|
Forum: MKIII Supra
09-01-2007, 01:50 AM
|
|
Replies: 23
Views: 7,296
Good idea, I guess
Well, that defintly sounds like the way to go, but I don't know anything about 1jz engines. What car do they come from? Will they swap out with the original 1991 mk3 without much of a fuss? Or are...
|
|
Forum: MKIII Supra
08-31-2007, 09:57 PM
|
|
Replies: 23
Views: 7,296
Used Supra engines from Japan. Are they OK?
I am thinking of replacing my whole engine (150,000 miles) rather than just changing the head gasket on my 1991 Supra. For $1,400 I can get a low mileage (40 to 60 K) engine from Japan. But I...
|
|
Forum: MKIII Supra
08-30-2007, 07:20 PM
|
|
Replies: 2
Views: 2,373
Which replacement head gasket is best??
Yes, it finally happend to my 1991 Supra, Blown head gasket.
I just want to use the most reliable gasket for long term use. I read that
Felpro makes one that is a little thicker, but doesn't need...
|
|
Forum: Exterior , Interior, and Detailing
08-20-2007, 03:09 PM
|
|
Replies: 1
Views: 2,670
Diagram or photos how to get interior panel off?
Hi. Now I know what needs to be done, but how to do it? I am trying to get the drivers side interior door panel off so I can replace the out side bumper molding. I tried unscrewing the obvious...
|
|
Forum: Exterior , Interior, and Detailing
08-14-2007, 06:10 PM
|
|
Replies: 1
Views: 4,333
Exterior door trim removal - How?
Hi - I want to remove the exterior horizontal trim from the right side door on my 1991 Supra to fix some rust that is there. How is the trim removed? Do you pry it off, or do you have to remove...
|
